Log In or Request an Account to see pricing and options.
This is a complete replacement kit consisting of the O-rings in the Control Valve.
Contains: O-rings
Download File:
UV-7B & BC Viton Seal Kit PDF
This is a complete replacement kit of the solenoid area of the UV-7B, UV-7BC Valve.
Contains: Solenoid Plunger Kit, Solenoid Hammer Kit, Solenoid Orifice
This can be ordered as either a single complete replacement kit (P/N 5106V) or as the following individual kits: Soleniod Plunger Tube Kit (P/N 5431), Solenoid Hammer Kit (P/N 5430), or the Solenoid Orifice Kit (P/N 5429). See EECO valve catalogue or the Technical Info PDF included here for parts included in each kit.
This is a replacement kit of the solenoid orifices of the UV-7B, UV-7BC.
Contains: Orifices, and O-rings
his is a replacement kit of the solenoid hammers of the UV-7B & UV-7BC Valve.
Contains: 2 NO & 2 NC Hammer Bodies, Hammers, and 2 Springs
Contains: 2 N/O & 2 N/C Plunger Tube Assemblies
This kit is designed to replace existing Bypass Pistons in the field.
Contains: Bypass Piston, O-ring, Spring Cap, and Spring.
This assembly is a replacement Down Piston for a UV-7B Control Valve.
Contains: Down Piston Assembly.
This assembly is a replacement Down Piston for a UV-7BC Elevator Control Valve.
Contains: Down Piston Assembly.
Cylinder Lifting Clamps (CLC) are designed to lift and hold hydraulic jack cylinders safely during construction. Constructed of formed steel bar for light weight and easy handling. These clamps are equipped with shackles for lifting and tensioning bolts for applying pressure around cylinder pipe.
Piston Clamp / Wrenches are designed to safely lift, hold, and tighten pistons during construction. The welded steel construction with replaceable tension pads and tensioning bolts for applying equal pressure around piston ensures higher griping force than wood clamps. Each clamp has a maximum rated load of 1950 lbs.
Model PCW-24 is designed for lifting from the handles. The handles on this model are not removable.
Models PCW-47 and PCW-712 have been designed for lifting from shackles that are supplied with the units. These models are equipped with removable handles for a more compact design during storage.
Custom sizes are available. Contact EECO for more details.
Note: To ensure safe lifting, holding and tightening, the piston and tension pads must be clean, dry and free of oil and grease. Also Piston Clamp / Wrench must be properly tightened around the piston.
(DURING LIFTING DO NOT ACCELERATE OR STOP QUICKLY)
PVC Lifting Clamps are designed to lift and hold flush joint PVC pipe safely. Constructed of formed and welded 1/4" steel plate for light weight and easy handling these clamps are equipped with two holding tabs and shackles for lifting. A tee bolt tensioner is used to apply pressure around PVC pipe with cupped set screws for gripping. The maximum rated load for the PVC Lifting Clamps is 3000 lbs.
Note: To ensure safe lifting and holding, the clamp must be properly tightened around PVC pipe by adjusting the cupped set screws.
The PeViCol PVC Cement was specially designed for gluing PVC pipe. This non-flammable cement does not require a primer. The low odor and low emissions allows to be used indoors with minimal ventilation. The cement can be used in a temperature range from 32º - 176º F (0º - 80º C). PeViCol PVC Cement, a NordColl product, is not classified as an environmental toxin and the solvents in solutions are biologically degradable.
EECOLube: The EECOLube is a performance improving friction modifier oil additive formulated to reduce "Stick Slip", rough starts & stops and prevent noise in hydraulic elevator systems. EECOLube is compatible with petroleum or biodegradable oils. EECO recommends using 1 bottle (quart) per 60 gallons of oil.
The Adjustable Spanner Wrench can be used on the Telescopic Jack’s Head Flanges. The wrench’s drop forged jaws are 3/8” thick with 11 adjustable positions for a capacity from 4-3/4” to 12-3/4” outside diameter and the handle is 1” in diameter and 24”’ long.
This Evacuation Pump is used to drain residual oil remaining in the space between the cylinder(s) and the piston(s) while disassembling the Telescopic Jacks to service the internal head(s). The pump has a 1/4" shaft to fit a drill motor (minimum speed of 800 rpm) and is supplied with 25’‐0” of flexible tubing. Longer tubing lengths are available. The pump has a maximum head of 55’‐0”, 1.8 gpm based on 1200 rpm, and operating temperature of 1200 F. Do not pump gasoline or other flammable fluids.