Control Valve Accessories
EECO Control Valve Accessories
These pages contain EECO Valve accessories for all of our Control Valves.
For accessories that fit a particular valve, click on the valve name below.
UV-4R • UV-5AT(C) • UV-7B(C)
This is an accessory for the Control Valve
Contains: Liquid Filled Gauge, Female Quick Disconnect
This is an accessory for the Control Valve to accept a Pressure Gauge Assembly
Contains: 90º Elbow, Tee, Shutoff Valve, Low Pressure Switch N.O. and Male Quick Disconnect.
This is an accessory for the Control Valve to accept a Pressure Gauge Assembly
Contains: Shutoff Valve, and Male Quick Disconnect
This is an accessory for the Control Valve
Contains: Low Pressure Switch N.O.
This is a replacement part for the pump port of the Control Valve.
NIPPLE PUMP INLET 2" GRV.
Contains: Grooved Nipple.
This is an adapter to convert the jack and/or tank port of the Control Valve to grooved.
ADAPTER 2" GRV UV5AT JACK/TANK
Contains: Grooved Nipple.
The Grooved Adapter Short was designed to convert the Jack and Pump port of the
UV-7B, & UV-7BC control valve from the standard NPT. This adapter threads directly
into each port.
The Grooved Adapter Long was designed to convert the Tank port of the UV-7B, & UV-7BC control valve from the standard NPT. This adapter is installed using the existing pump port flange and hardware.
Used with the UV-7B & UV-7BC Control valves, this Pressure Gauge Fitting & Low Pressure Switch System is used to provide a
means of attaching a Pressure gauge to the control valve. It is provided with a 1/8
brass shut off valve and a male quick disconnect fitting and a low pressure switch.
The option of a N.O or N.O./N.C switch is available. Click Here for details.
Individual fittings can be purchased to create your own arrangements.
See page 75 for more details. Part No. 5707.
Note: This product does not include the Liquid Filled Pressure Gauge Assembly.
The UV-7B(C) Pressure Gauge Fitting System is used to provide a means of attaching a Pressure gauge to the control valve. It is provided with a 1/8 brass shut off valve and a male quick disconnect fitting. Individual fittings can be purchased to create your own arrangements. Contact EECO for details. Part No. 5706.
This is an accessory for the Control Valve
Contains: Low Pressure Switch N.O./N.C.
The Pressure Gauge Fitting & Low Pressure Switch System is used to provide a means of attaching a Pressure gauge to the control valve. It is provided with a 1/8 brass shut off valve and a male quick disconnect fitting and a low pressure switch. The option of a N.O or N.O./N.C switch is available. Part No. 5707
Standard mounting arrangements of a pressure gauge fitting with shutoff valve on the Jack side of the check valve on a UV-4R, in accordance to ASME A17.1/CSA B44 3.19.4.5. The flange is part of the valve and is shown for illustration purposes only.
The Pressure Gauge Fitting System is used to provide a means of attaching a Pressure gauge to the control valve. It is provided with a 1/8 brass shut off valve and a male quick disconnect fitting. Individual fittings can be purchased to create your own arrangements. Contact EECO for details. Part No. 5706
Standard mounting arrangements of pressure gauge fittings with shutoff valve on the Jack side of the check valve on a UV-4R, in accordance to ASME A17.1/CSA B44 3.19.4.5. The flange is part of the valve and is shown for illustration purposes only.
EECO Valve Troubleshooting Kit for UV-5AT(C) & UV-5BT(C). Also available for UV-4R and UV-7B(C) Control Valves.
This kit provides parts commonly required during control valve service
Contains: Valve Catalog, Troubleshooting Guide, USB Flash Drive, Combo Wrench, 110vac Coil (Black Wire), 220vac Coil (Black Wire), Dynamic Seal Kit, and Solenoid Kit
This is an accessory for the Control Valve
Contains: Liquid Filled Gauge
FEMALE QUICK DISCONNECT, 1/8"FEMALE
This is an accessory for the Control Valve
Contains: Female Quick Disconnect
MALE QUICK DISCONNECT, 1/8"FEMALE
This is an accessory for the Control Valve
Contains: Male Quick Disconnect
1/8" SHUT OFF VALVE, MALE X MALE
This is an accessory for the Control Valve
Contains: Shutoff Valve
1/8" 90° ELBOW, MALE X FEMALE
This is an accessory for the Control Valve
Contains: 90O Elbow
EECO’s Load Weighing Kit (LWK) is an addition to a new or existing Power Unit to prevent the elevator from being overloaded. The switch can be wired into the controller, if the provision is available, through either a normally open or normally closed contact. The kit consists of a field adjustable pressure switch with 48” wire leads, a 4-1/2” long grooved nipple (2”, 2-1/2”, 3”, & 4” sch 80), a 1/2” flex 90° screw-in conduit fitting, and (3) 5’-0” extensions of 18 awg wire with butt splices and #8 spade terminals.
Load Weighing Switch also available separately. Part No. 5719
Right Hand Jack Port Adapter Kit for the UV-5AT(C) Elevator Control Valve, Part # 5709. Contains: 1 Right Hand Adapter Assembly, 1 Grooved Adapter, 1 Groove Clamp
Right Hand Jack Port Adapter Kit for the UV-5BT(C) Elevator Control Valve, Part # 5753. Contains: 1 Right Hand Adapter Assembly, 1 Grooved Adapter, 1 Groove Clamp
Also available for UV-4R and UV-5 Series Control Valves.
This kit provides parts commonly required during control valve service
Contains: Valve Catalog, Troubleshooting Guide, USB Flash Drive, Combo Wrench, 110vac Coil (Black Wire), 230vac Coil (Black Wire), Dynamic Seal Kit, and Solenoid Kit.
Also available for UV-5 Series and UV-7B(C) Control Valves
This kit provides parts commonly required during control valve service Contains: Valve Catalog, Troubleshooting Guide, USB Flash Drive, Combo Wrench, 110vac Coil (Black Wire), 24vdc Coil (Black Wire), Dynamic Seal Kit, and Solenoid Kit.
This kit is used to convert an existing, in-service, UV-7B valve into a UV-7BC (Constant Down Speed) valve.
Coil Kit for UV-7B(C) EECO Control Valves. Kit contains 4 coils.
A Dynamic Viton seal replacement kit (P/N 5131D) for your in-service UV-5A series valves (including UV-5A "S" series, UV-5AT and UV-5ATC valves). This kit contains the O-Rings for the moving parts of 3 Valves.
Since January 2001, all EECO valves have been manufactured with Viton seals. If you are replacing any of the major components listed on this page (which are supplied with Viton seals) in an EECO valve manufactuered prior to January 2001, EECO recommends that you also replace the older valve seals in the remainder of the valve with the newer Viton seals.